profilux 3
Type: Posts; User: johnfallon135
profilux 3
but the first 2 you described are L1/L3 which are + and - and remaining 2 wires L2/L4 are also + and -
10498
which are the ones that light up the diode and does it matter which + order...
so I'm guessing the first 2 wires are live and the remaining 2 are dead wires? if so how do you tell the difference from the first 2 with a battery and diode does it matter which is + and - in pin 1?
is there a fix for this line at the bottom of my screen? thanks
10496
the device itself doesn't ask for a update confirmation it just stays in its normal screen
if this helps after i click ok on the error 41 message box this message box then pops up
8587
thanks this worked to connect my profilux to profilux control however when i click on File --> Firmware - Update Profilux then select the ProfiLux3_V629.mhx file the update begins but then at 99%...
i never said i was able to connect to ProfiluxControl that's the problem here was that i COULDN'T connect to ProfiluxControl. This entire time vinny was trying to help me update my profilux outside...
when i click the connect button in the Profilux Control program it says "the connected profilux has a too low firmware version and can't be used with this version of profilux control" this is version...
thanks for helping me matthias. yes the profilux still starts with the firmware 5.14
thanks matthias my PL3 does enter bootloader mode. when i take the power off then back on during the reset message the PL3 screen blacks out which i'm assuming is the bootloader mode? however i still...
hey vinny just wondering if you're looking into this as i was hoping to get it working by the weekend thanks!
8568
8569
during this time i unplug the power to my profilux then plug it back in. also tried leaving the plug out prior to the reset message then plugging it back in during the reset message...
okay so i restarted my computer and tried it again but it now says "ERROR!! No.001 Download error" at 3/7 of the download
thanks so i got everything working now but i get stuck on the flash programmer after i click full operation it says "please push reset button on user board" then i plug my profilux back in then it...
my GHL Control Center folder only contains:
(Folder) GHL Control Center
(Folder) Tools --> Flasher shortcut
GHL Control Center shortcut
Unistall GHL Control Center shortcut
i searched my...
i connected the rs232 cable to my computer and under COM and LPT in the device manager it just says "prolific USB-to-Serial Comm Port (COM4)" with a exclamation mark and i updated it. it doesn't say...
i got my ip address however
after creating a new connection in PC with my IP address it said the firmware is too low to connect.
after creating a new connection in GCC with my IP it says...
5.14
thanks vinny i got the usb however it says that my profilux III firmware is too old to work with my GCC.. how do i update it?
i understand the controller wirelessly tells the pumps what to do just wasn't sure what was the point in the profilux vortech's controller's second pab port. why would someone want to hook the second...
what's the point of the second port on the vortech controller then?
is 1 pab port good enough for 2 powerheads or is each port on the controller for each powerhead? i noticed there's 2 ports thanks
thanks vinny is there a way to do it without the usb as i lost my usb cable i might just have to go out and get one.. also if i don't have my lan settings still set to automatically have an ip...
i connected my profilux directly to my modem via ethernet/lan cable however GCC just says not connected. is there a step i'm missing? how can i get GCC to connect/recognize my profilux III? thanks!
i'm tired of inputting all my settings again after a power outage or moving my profilux to a different socket is there a way i can have the settings permanently saved? thank you!