When measuring and calculating the sample hose length for volume, are you including the 4" for the line in the dosing pump head?
Also make sure to mine the tubing ID, the hose GHL provides is 4mm...
Type: Posts; User: ReefClownMIA
When measuring and calculating the sample hose length for volume, are you including the 4" for the line in the dosing pump head?
Also make sure to mine the tubing ID, the hose GHL provides is 4mm...
I would give that a try.
https://www.aquariumcomputer.com/downloads/wifi-module-esp-update/
WiFi_FirmwareUpdateTool.exe -> Erase & reprogram filesystem...
You can update your WiFi firmware with the update tool:
https://www.aquariumcomputer.com/downloads/wifi-module-esp-update/
What version of Windows are you on?
-> Did you reload the driver, or restore last good known?
LAN is always better than WiFi, less chance for interference. If that’s an option, I’d go that route :)
This is usually due to a weak WiFi signal, or interference on the channel your WiFi is currently running.
What firmware version is the Doser currently on? Make sure to upgrade to latest version if...
@mortie31 -
GCC 1.1.0.5 has been posted today.
New in V1.1.0.5:
Support for GHL Doser Maxi added
Firmware ProfiLux 3 V6.31 and ProfiLux 4 V7.09, needed for GHL Doser Maxi Slave, included
There will be an update later today, I believe.
It's a combo FW release that will support both Maxi & KHD, it's been in test release for some time. :)
Ahh, yes - the hanging kits became optional due to customer feedback some time ago, including the 6X00's.
Many customers mount the lights via alternate ways and found the prepackaged hanging kit...
While the alternating ramp of the pumps is possible, via the Stream Groups, there is not a tie-in to the Stream groups from the Flow Sensor. The flow sensor is set to a static value, and will...
LX7's have the Power Balancing, this is a hardware feature, not software
hmmnn. Not sure what you mean with the Support is not included like the 6200's. :/
Have you cleaned it, then reset and moved up/down, above and below water to see if it shows reaction in GCC under "SETTING AND STATES LEVEL-SENSOR INPUTS"
I'm just going to throw this out there,...
I'm using a Madison submicro floatswitch on an ADIN card, works a treat!
Hi, ja nach dem umstellen erst speichern, dann Kalibrieren. Ansonsten kalibriert das mit der vorherigen gespeicherten Einstellung.
Have you toggled the sensor(s) to see if they respond in GCC ?
Can you post a screenshot of your ATO configuration showing the sensors?
Also make sure that your cables are connected snug, if...
I can't think of any way to make this work with the flow sensors, as they are not ramp-able. The flow rate on the flow sensors is statically set, and will maintain the flow at said rate.
What you...
No worries at all - happens to the best of us. :)
Make sure you're using the correct FIRMWARE update mode, and not the PAB Device update.
Here is the HowTo video, just as a refresher :)
https://www.youtube.com/watch?v=Fj0SH93QoKc
Yes, this is possible with a 0-10v controllable return pump.
https://www.reef2reef.com/threads/flow-sensors-usage-and-example-setup.261199/
Correct, v1.0.9.9 & fw 7.07 contain the email notifications.
What country, and ISP are you on?
Sounds like your LFS ordered an upgrade kit for the Doser 2.
Hi Lincsreefer,
A couple of questions:
When you say you have ports forwarded etc, are you accessing the PL4 from a remote network/location? Over the internet?
What is your PL4 firmware and WiFi...
Hi Jay - have a look at this, was posted on one of the prior pages in this thread.