Hi,
you are going to need to provide more information than that. I had a look at the stray light website and there isn't very much information on the dimming function:
SeashineTM fixtures can be...
Type: Posts; User: camnbron
Hi,
you are going to need to provide more information than that. I had a look at the stray light website and there isn't very much information on the dimming function:
SeashineTM fixtures can be...
A solution to this problem has been found by our collegues on the reef central forum.
Osram 1-10v signal amplifier
this will boost the maximum from 10mA as specified earlier in this topic to...
If you have the EVG board that has the relays on it and are using that to connect to the meanwell dimmable drivers, then you plug the AC lead from the EVG board into a standard AC wall socket.
Anyone here :) I'll try to provide some information based on your first post.
Assuming you are having 4 tunze streams utilising L1-L4, you will need:
2 x splitters (one for L1 & 2, the other for...
When you are adjusting the pots inside the driver:
SVR1 = Output voltage adjustment
SVR2 = Output current adjustment
that is as shown on
meanwell.com specsheet for ELN-60
If running the LED's in...
Hi jdrabek,
Good to see more people having a go. My LED's finally arrived as have my drivers. Now all I need is a quite time at work to do my homie! Great to see others doing the same type of...
"What is your favorite aquarium controller from 2009?"
considering when the PIII was released would it not have been better to have the PII in the list instead?
By having the PIII option only...
OK. The P3's been launched.
Hows the work going with the vortech control!??!?!?
:D
A countainer to hold the water and a pump to pump the water from said container to top up the tank. The pump is plugged into an outlet on your powerbar.
So items required:
1 x water container
1 x...
Thanks for that Luisagos saved me finding it :)
Hi nallaak.
I think you might having the 1-10v dimming control signal to the Meanwell Driver confused with the output from the Meanwell Driver to...
Sorry for the confusion Matthias.
I'm not very good at describing things, but I believe you have answered my question anyway lol. Here is another way of describing what I am intending on doing:
...
Heres the link to the downloadable manual for the EVG-AP2 if that helps:
http://www.aquariumcomputer.com/Download/Manual_EVG-AP2_V400.pdf
Ok this is the reply I got on the nano reef forum regarding the 2 different cards:
Either or. At 0v, there is no ooutput from the driver. No need for a relay at that point. The relay might be...
Thanks for that.
I too am not sure that the meanwell LED driver really needs a cut off. Based on the information I have read on the Nanoreef forum, it isn't, but I will post up something there...
Hi again Martin,
what would be our better option out of the two? I only have experience with the EVG card because I use one for my dimmable Osram T5 ballasts. Hence my above post.
The LBFAP...
Really?
I thought it would have been better to use the EVG-AP-1F to also switch off the power supply to the Meanwell driver as well?
I'm intending on doing this same thing on my tank upgrade next...
It would be expanding on switches that are already available, but allows the user to define their purpose.
For example:
A person may have their sump in a basement, below the display tank. Their...
What about a digital input card?
This would allow people to have the ablility to configure buttons for situations where they are unable to communicate with the Profilux by the buttons on the front...
I think I have the same issue. I have 2 tunze nano 6055's that are set up to stop during feed pause.
During normal operation they ramp up and down in speed - that is fine.
During feed pause they...