Search:

Type: Posts; User: frankvanes

Search: Search took 0.01 seconds.

  1. Well I never really enabled it on purpose. I just...

    Well I never really enabled it on purpose. I just checked:

    With and older firmware the button is gone, even when at R/W. After the update I didn't re-check in GCC. Now I have and it was indeed on...
  2. Save Icon missing in Doser 2 section of MyGHL

    Mine too. I just updated the fw to the latest version just to be sure. But the result is still the same. In GCC it works fine. But as a MacOS / iOS user I prefer to use MyGHL.

    (support for the...
  3. Same here for MyGHL and PF3 with attached doser...

    Same here for MyGHL and PF3 with attached doser (1). I cannot save the refilled amount in MyGHL. The save button is gone and OK does not set the refilled amount. Please help! This is one of my...
  4. Replies
    0
    Views
    2,317

    Updated app for Profilux?

    Hi

    Will there be an update soon containing the ability to adjust the doser and reset the container from the app? This would be an awesome addition for me.
  5. Replies
    14
    Views
    6,992

    Strange behaviour for dimmable GHL T5 bar

    Looks like I spoke too soon. :( When I looked this morning it was starting up just fine but when I returned from my daughters swimming lesson at noon the unit was off again.

    Manually switching...
  6. Replies
    14
    Views
    6,992

    Hi Carolin No I was unable to before because...

    Hi Carolin

    No I was unable to before because the PF3 unit was built-in very tightly. I changed this recently and have switched the streamer and light ports. And what do you know?! It works! I am...
  7. Replies
    14
    Views
    6,992

    I Had a little time this morning to check on the...

    I Had a little time this morning to check on the lights. They seem to be getting worse. Even switching from 0 to 100% does not seem to be reliable anymore.
    When I power them on I see a short flash...
  8. Replies
    14
    Views
    6,992

    Oh, just when it's at 0%. Probably just the EVSA...

    Oh, just when it's at 0%. Probably just the EVSA switching off and on.
  9. Replies
    14
    Views
    6,992

    I use brand new ATI tubes burned in for >60 hours...

    I use brand new ATI tubes burned in for >60 hours and they have about 350 hours of use right now.
  10. Replies
    14
    Views
    6,992

    Partly. This is still an issue, but one I can...

    Partly. This is still an issue, but one I can work around as I do not normally do this. I dimm up from 0% to 75% in small steps and in the evening I dimm back down from 75% to 0%.

    What has...
  11. Okay, time for a follow-up on this one. I...

    Okay, time for a follow-up on this one.

    I have been fiddling with this for a long, long time and finally figured out what was going on. My electrical installation is leaking a tiny amount of...
  12. Replies
    14
    Views
    6,992

    Unfortunately the last two days I had the problem...

    Unfortunately the last two days I had the problem again. When fiddling with the settings the lamp reacts, especially after going back to zero and then to 100%. You hear a distinctive 'click' when...
  13. Replies
    14
    Views
    6,992

    I've been running it in "Burn-in" mode for two...

    I've been running it in "Burn-in" mode for two days and everything is allright.
    I did fiddle with the dimming some more and my conclusion is:

    Switch Off -> 100% ...
  14. Replies
    14
    Views
    6,992

    Yes, the voltages are 1V minimum and 10V maximum....

    Yes, the voltages are 1V minimum and 10V maximum. This morning it ramped up to 100% immediately (due to the burn-in setting I set up I guess). So it did what it had to do. I will keep a close look on...
  15. Replies
    14
    Views
    6,992

    Strange behaviour for dimmable GHL T5 bar

    I recently bought a second hand T5 dimmable light bar from a fish store (ALB2F1D54-T5) here in the Netherlands.
    It seemed to be working at first but now I start programming it I see some strange...
  16. Flashes occur with connected Aquaray (SunaEco) light bars

    Hi,

    I have two TMC Aquaray light bars connected to my 6-way powerbar as additional lighting fir my tank. This is connected to a PL3 box (fw 6.06). At a certain moment (might have been after...
  17. Thread: email issue

    by frankvanes
    Replies
    4
    Views
    2,268

    Same here :( It started after upgrading to...

    Same here :(

    It started after upgrading to version 6.06 coming fro a 5 version (not sure which version exactly.)
    When pressing the test button from PL Control it works just fine. I tried...
  18. That's a shame, the data is already there, it...

    That's a shame, the data is already there, it would be easy to program IMHO. Anyway, thanks for the quick reply.
  19. Email alert after set # of operation hours for lightbulb

    Hi,

    Is it possible to create an alarm/alert after a set number of operation hours for in my case T5 bars? I'd like to be informed when my lights are due for a change. As not all bars run the same...
Results 1 to 19 of 19