I have a sump with covers and wish to place ph and temperature probes within. I have read not to completely submerse ph probes for anything other than a short period but can I use these probes in a...
Type: Posts; User: Tinpot
I have a sump with covers and wish to place ph and temperature probes within. I have read not to completely submerse ph probes for anything other than a short period but can I use these probes in a...
Yeah, that was it. I feel so stupid now ! :-)
I have a profilux 4 which is currently running firmware v.706. When I try to update the firmware to either v7.07 or v7.08 I get the error - Firmware not suitable for this device. I have tried doing...
Well that's strange because an email notification I have received earlier, quotes yourself - "This is a revised version of 7.05". But now I cannot see that post anywhere. Can you clarify ? I have...
Wasn't Firmware v7.05 released with GCC v1.0.9.5 ? How will this new version of GCC improve the noise immunity of the digital temperature sensor if it does not include new firmware ?
I'm not sure if this helps or not but I have the conductivity probe on a freshwater tank and I am not experiencing this issue.
Happy to have helped :-)
Did you upgrade GCC from GCC v1.0.9.3 to v1.0.9.5 ? I also had this issue but in my case I had upgraded from v1.0.9.4 and it appears that during the upgrade process the latest rom was not...
Tank is 162cm x 100cm (wide) x 70cm. Lit by two Mitras Lightbar 2 'Daylight' controlled by a Profilux 4 which also controls temperature and monitors pH and conductivity. Filtration is a Royal...
I have measured mine and it is 2m
Have you tried the Mitras Lightbar in the onboard RS232 ? I have two Lightbar 2's connected to the onboard RS232 and they work perfectly ie dimming, seasonal lighting etc.
I've resolved this by using the comm port driver from this thread: http://forum.aquariumcomputer.com/showthread.php?11979-Update-7-02-auf-7-03-schl%E4gt-fehl
I've sorted my problem by using the comm port driver from this thread: http://forum.aquariumcomputer.com/showthread.php?11979-Update-7-02-auf-7-03-schl%E4gt-fehl
Have you tried updating the Profilux 4 Firmware yet ? I ask because I am having a lot of trouble connecting to the P4 using GCCv 1.0.9.4. I finally managed to make a connection yesterday evening and...
Yes I have tried adding a new device but I still cannot connect. if I open Administrate... Connections dialog it shows the original connection and the new connection. I then tried deleting the old...
I have had GCC v 1.0.9.2 running without issue. I have tried several times to install v 1.0.9.4 but each time it fails to connect. If I use the button to check devices, no devices- none at all -...
KH Director sounds more like an Alkalinity controller.
OK. Thanks. But there is no mention of this in the manual.......
I had to select Saltwater then calibrate using the 50mS calibration soultion then change probe setting to (F)reshwater. Is this correct ? If I tried to calibrate it using the 50mS solution with the...
You could connect the ballasts to a switchable plugbar (if you have one) and switch the socket on/off at the appropriate times
I have also been using 1.0.9.2 since Monday to set up my P4, probes etc and Mitras Lightbar schedules and I haven't found any issues with it.
They don't know who and when ? I thought they were supposed to be shipped out in the order that the orders were placed. Mine was supposed to be shipped late last week or early this week according to...
As I'm expecting my Profilux 4 this week will Control Centre version 1.0.9.1 be suitable or is there a newer version about to be released ? I've looked through the change log of v1.0.9.1 and it...
Thank you.
I did, after your suggestion. Still waiting for a reply....