View Full Version : Profilux email works no information but how to get the data and alarm info
I have been received email from Profilux but it's empty.I tied ProfiLuxControl 5 and 6 both work but no info in it. How to add such as sensor datas and Alarm info etc.
Thanks for the help!
Won
I have been received email from Profilux but it's empty
PLII or PL3? Sent from PLC Software or from PL3 directly?
If it´s from PL3 sent directly:
At first you have to ensure that you have the latest firmware 5.05f
Then you have to set up a mail template with the codes from http://support.aquariumcomputer.com/german/download.php?did=144
Blahenazo
04.02.2011, 09:20
this is the template I use ( found it on the forum, and adapted a little bit it to my setup)
and this is nearly the max of the template (a few chars more and you not able to add more chars into PLC :(
$$ALMS$$
S
$$REPS[32][00]$$ $$SENN[xx]$$ - $$SENV[xx]$$
$$REPE$$
I
$$REPS[32][01]$$ $$ILLN[xx]$$ - $$ILLV[xx]$$
$$REPE$$
S
$$REPS[32][02]$$ $$SWIN[xx]$$ - $$SWIS[xx]$$ [$$SWIC[xx]$$]
$$REPE$$
L
$$LEVN[0]$$ - $$LEVV[0]$$
$$LEVN[3]$$ - $$LEVV[3]$$
Yes it's from PL3 sent directly and Yes I am using 5.05f.
Please explain more details about how to set up a mail template with the codes. should I copy this and paste to some where?
Thank you for your help
Blahenazo
06.02.2011, 10:57
you have to create a new email message ( in plc )
And as a contents of this message you can put the above template
in my case this will generate a email like this
then you can customize the template to your setup ( chosing the correct the lvl sensors ) I have levle 1 and Level 4 etc...
no alarm - all OK
S
pH-value 1 - 7.71pH
Temperature 1 - 25.1C
Conduct.(S) 1 - ---
Redox 1 - ---
pH-value 2 - 7.96pH
Temperature 2 - ---
Conduct.(S) 2 - ---
Redox 2 - 428mV
I
Illumina. 1 - 0%
Illumina. 2 - 0%
Illumina.10 - 0%
Illumina.11 - 0%
S
S 1 - Off [0.0 A]
S 2 - Off [0.0 A]
S 3 - Off [0.0 A]
S 4 - Off [0.0 A]
S 5 - Off [0.0 A]
S 6 - On [0.0 A]
S 7 - On [0.0 A]
S12 - Off [0.0 A]
L
Level 1 - Off
Level 4 - On
Thanks very much that works!
Thanks very much that works!
+1
This is good information , pls pin to the sticky
mine does not work properly :
why i will 2 emails at one go
this is the content of the email
Alarm: Temp 1
S
pH-value 1 - 7.27pH
Temperature 1 - ***
S
L
Level 1 - On
Level 4 -
template i used
$$ALMS$$
S
$$REPS[32][00]$$ $$SENN[xx]$$ - $$SENV[xx]$$
$$REPE$$
S
$$REPS[32][02]$$ $$SWIN[xx]$$ - $$SWIS[xx]$$ [$$SWIC[xx]$$]
$$REPE$$
L
$$LEVN[0]$$ - $$LEVV[0]$$
$$LEVN[3]$$ - $$LEVV[3]$$
why i will 2 emails at one go
How should we know? Maybe it´s cause you have programmed it.
Alarm: Temp 1
Temperature 1 - ***
In general it looks good, but you have a prob with your temp probe I think
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.